Ways to relocate a baby grand piano

Pianos regularly make movers yearly list of products that are most often harmed. Grand pianos are specifically troublesome. Practicing the following treatments for taking apart, padding and packing grand pianos will prevent damage, lower claims expense, and enhance customer fulfillment.

1) At least 3 people are needed to deal with a baby grand piano. If the infant grand piano requires to go up or down stairs or if a complete or performance grand piano requires to be transferred, a minimum of 4 people are needed.

2) Constantly finish a thorough and accurate inventory. It may be preferable or required to utilize a visual stock to properly describe and reveal pre-existing damage.

3) As numerous parts are taken apart, please location all hardware in a properly labeled parts bag and then put the parts bag in a "Parts Box".

4) Eliminate the music rack (lyre) from its track by pulling it toward the keyboard. Wrap it in a clean furniture pad.

5) Disconnect the lid by removing the hinge pins. Have someone wiggle the lid, holding it opposite the hinge, while a 2nd individual works the pin loose. Please beware not to harm the wood with the pliers or with the pin itself. If necessary, cover the jaws of the pliers with a little fabric to assist prevent damage to the wood. Wrap the lid in a clean furnishings pad.

6) Get rid of the prop that holds the cover open and cover it in a tidy furniture pad. The prop has a hinge pin and remains in 2 pieces.

7) Eliminate the pedal assembly and cover it in a tidy furniture pad. The braces at the rear of the assembly rest in slots at each end. When getting rid of the screws, please be mindful not to drop the braces. In addition, please be particularly careful with the push-rods so that they will not get bent. As you deal with the piano, number the push-rods from left to right as "1", "2", and "3", by placing a piece of masking tape with the proper number on each rod. Note: If masking tape is not available, please use properly labeled parts bags for this function. When reassembling at destination, please make certain to put the rods in the right order so that the pedals will work properly.

8) Pad the piano by placing a clean rolled furniture pad (stretch-wrap the pad to avoid it from unrolling) on the cover of the keyboard to avoid it from tumbling open while you deal with the piano. Cover the top of the piano with 2 tidy furnishings pads, neatly folded around the keyboard. Use rubber bands to secure the pads. Note: Please ensure that the surface of the piano is dust-free before padding it. Padding a highly refined surface that is dusty may cause great scratches, specifically on a black lacquer surface.

9) Position a piano board and connect the straps so that it is prepared to receive the piano. The raised brace on the piano board should be at the keyboard end of the piano.

10) Eliminate the left front leg by placing one person below the piano at the left end of the keyboard. Be sure to have two individuals raising the corner of the piano while the 3rd individual eliminates the leg. Keep in mind: Please be sure to note which legs were eliminated from which positions since some pianos have legs that are not interchangeable.

11) Place the piano on the piano board by decreasing the "leg-less" end onto the board. Please be sure to raise the whole piano a little while completing this maneuver to prevent unnecessary pressure on the staying, connected legs as the piano ideas. Raise the piano to an upright position on the board. Keep in mind: Please ensure that the soundboard is protected before raising. Make certain that the piano is focused comfortably against the brace at the end of the piano board. Note: Never leave the piano unattended. Always have at least one their explanation person holding the piano consistent at all times.

12) Remove the 2 staying legs and cover them in clean furniture pads. These legs are kept in location by a "essential and slot" arrangement. To get rid of the leg, slide it inward towards the center of the piano till it comes out of the slot.

13) Protect the piano to the piano board by bringing the ends of the straps together and fastening them. Location folded burlap pads over the furniture pads however under the straps to offer additional defense to the edges of the piano. To avoid the strap near the narrow end of the piano from slipping off, connect the loose ends of the two straps together.

14) To move the piano over a flat, level surface area, tilt the piano and piano board and place a four-wheel dolly under the center of the piano board.

15) To move the piano up or down stairs, utilize the piano board as a skid. After sufficiently padding the stairs for defense against residence damage, put the keyboard end of the piano toward the bottom of the stairs. Connect a hump strap to the leading end of the piano board to prevent the piano from slipping.

16) To pack the piano, leave it on the piano board and place it in a tier as the first base product with the keyboard facing the wall of the preceding tier. The finest place to fill the padded cover is in between the piano and the preceding tier or between the wall and the piano.

Grand pianos represent a substantial challenge, they can be moved without damage by using common sense and practicing the treatments listed above.

Leave a Reply

Your email address will not be published. Required fields are marked *